Where to buy | Partner Portal | eShop

8-Port Power Over the NET™

Discontinued
PN0108
  • Remote power on / off / reboot control for eight outlets via TCP/IP and a built in RS-232 PON (Power Over the NET™) port
  • Local power on / off / reboot control via the PN0108's PON port to the computer's RS-232 port
  • Daisy chain up to 15 additional stations to control up to 128 outlets
  • Manual switching between Local and Remote access for each port via front panel push button switches
MSRP: Quote Upon Request

Altusen's PN0108 is equipped with eight hotpluggable ports for easy server rooom management. Each port can be individually controlled so that users can set the power on sequence and delay time for each port to allow equipment to be turned on in the proper order. On/Off scheduling allows for preset start/shutdowns/restarts on a daily, weekly,monthly basis.The PN0108 is the most convenient, reliable and cost effective way to obtain access to your server room remotely.*

Package Contents

  • 1x 8-Port Power Over the NET™
  • 1x AC Source Power Cord
  • 8x Power Outlet Power Cords
  • 8x Safe Shutdown Cables
  • 1x PON Cable (DB9 F to DB9 M)
  • 1x User Manual
  • 1x Quick start guide
  • 1x Mounting Kit :Rack mounting brackets and hardware
  • 4x foot pads
  • 1x Software CD
  • Remote power on / off / reboot control for eight outlets via TCP/IP and a built in RS-232 PON (Power Over the NET™) port
  • Local power on / off / reboot control via the PN0108's PON port to the computer's RS-232 port
  • Daisy chain up to 15 additional stations to control up to 128 outlets
  • Manual switching between Local and Remote access for each port via front panel push button switches
  • Individual control of each port - users can set the power on sequence and delay time for each port to allow equipment to be turned on in the proper order
  • Easy setup and operation via a GUI interface
  • Provides three configuration/management methods: Browser; Telnet; or Console Terminal
  • Safe shutdown and rebooting for Windows systems*
  • Overcurrent protection and recovery for each AC port (110 V model only); total port overcurrent protection (both models) - remote users can monitor the outlet status via the GUI interface
  • Separate circuits for the unit's power and the power to the devices - the power control status menu is still accessible even when an overcurrent condition trips the devices' circuit breaker
  • On/Off scheduling - allows everything from a one-time start/shutdown, to daily, weekly, etc. starts/shutdowns at user-specified times
  • Port grouping - perform the same action on a specified group of ports
  • LEDs for easy status monitoring
  • Two level (Administrator and User) security
  • Configuration can be reset
  • Firmware upgradeable - daisy chained stations receive the upgrade via the daisy chain bus
  • UL/TUV approved
  • Multiplatform support: Windows 2000/XP/Vista, Linux, Unix and FreeBSD.

    *Safe shutdown and rebooting is supported if the Power Monitor utility has been installed
  • For more information about KVMs which can connect to PN0108, see Compatible KVM Table

    *The PN0108 is not a stand-alone unit. It must be connected to the CN6000, PN9108, SN0108 or SN0116 to access these features
Power Inlets1 x IEC 60320/C14 Male
Power Outlets8 x IEC 60320/C13 Female
Connectors
PON In1 x DB-9 Female (Black)
PON Out1 x DB-9 Male (Black)
Safe Shutdown8 x 6-pin Safe Shutdown Jacks Female (Black)
Switches
Reset1 x Semi-Recessed Pushbutton
Power1 x Rocker
Firmware Upgrade1 x Slide
Outlet On/Off8 x Pushbutton
Remote On/Off8 x Pushbutton
LEDs
Power Outlets8 (Orange)
Remote8 (Green)
Station ID2 x 7 segment (Orange)
Maximum Input Power Rating100 ~ 120V, 50/60Hz,12A
220 ~ 240V, 50/60Hz,10A
Power Consumption120V/1440W; 230V/2300W

Note:
● The measurement in Watts indicates the typical power consumption of the device with no external loading.
● The measurement in BTU/h indicates the power consumption of the device when it is fully loaded.
Environmental
Operating Temperature0 ~ 40˚C
Storage Temperature-20 ~ 60˚C
Humidity0 ~ 80% RH ,Non-condensing
Physical Properties
HousingMetal
Weight3.70 kg ( 8.15 lb )
Dimensions (L x W x H)43.72 x 21.83 x 4.40 cm
(17.21 x 8.59 x 1.73 in.)
NoteFor some of rack mount products, please note that the standard physical dimensions of WxDxH are expressed using a LxWxH format.





DescriptionVer.Release DateFile Name
Firmware Upgradev2.0.1952010-11-01 pn0108_v2.0.195.zip
Firmware Upgradev2.0.1912009-06-29 pn0108_v2.0.191.zip
Firmware Upgradev1.9.1812007-09-05 pn0108_v1.9.181.exe
Firmware Upgradev1.8.1722007-04-13 pn0108_v1.8.172.exe
Firmware Upgradev1.6.1532005-11-23 pn0108_v1.6.153.exe
OSDescriptionVer.Release DateFile Name
Others
PMonitor Release Notev1.1.1012006-04-21 pn0108_PMonitor_v1.1.101.pdf
Java Clientv1.6.1532005-11-23 pn0108_Java_Client_v1.6.153.exe
PMonitorv1.1.1012005-09-16 pn0108_PMonitorSetup_v1.1.101.exe
We are here to help! Please visit ATEN eService for technical assistance.